減速機如何修復
減速器是感應電動機。其工作原理是在元件更換時使用電子電路提供直流電源。多相定時控制電流，使用此電流為減速器供電，減速器可正常工作，雖然減速器已被廣泛使用，但減速器不像普通直流電機那樣工作。交流電動機在正常條件下使用。如果您遇到問題，我們需要學會修復它。
1.根據減速器上標記的電阻值測量電阻。減速器分為兩個繞組。兩個繞組的結構完全相同。每個繞組的中心端對稱地等于另一端，并且標簽的電阻值是一致的。不同電機引線的順序是不同的。
2.測量時，可以測量兩個繞組的電阻值是否相等，并且應與電機標記一致，然后使用電源測試。在測試過程中，電源的兩極交替接觸每個繞組的兩端。步進旋轉，步驟同樣強大，否則電機損壞。
3.使用減速器上標記的電源電壓進行測試。如果電機上沒有標記，請從較低電壓開始，然后逐漸增加電壓進行測試。電源的一端連接到某個繞組的中心端，另一端連接到電源。一端交替接觸繞組的另一端。此時，減速器應逐步旋轉，每一步應同樣強大，否則電機會損壞。
當前位置：